Dust removal equipment features

The foam acts on the dust through good coverage, wetting, adhesion, etc., effectively reducing the dust concentration on the mining face, greatly improving the working environment of the mining face, improving the working efficiency of the underground workers, and effectively reducing the dust of the first-line workers. The incidence of the disease.

Compared with other wet dust suppression methods, foam dust suppression can reduce water consumption by 50% to 80%, and dust suppression efficiency is 3 to 5 times higher than spray watering. Foam dust suppression has the following characteristics:

1. The foam can cover the dust source without voids, and fundamentally prevent the dust from spreading outward;

2. After the liquid forms a foam, the total volume and total surface area are greatly increased, the collision efficiency with the dust is increased, and the working environment of the underground mining face is purified;

3. The liquid film of the foam contains special additives, which can quickly change the wet performance of the dust and increase the speed at which the dust is wetted;

4, the foam has a very good viscosity, the dust and foam will quickly adhere to the foam after contact.

5. Suppress the spark generated by the boring machine pick and the action of coal and rock, and eliminate the gas and coal dust explosion accidents.

6. The water consumption is small, which avoids the sinking of the comprehensive excavator caused by the large amount of water and dust removal, and improves the working efficiency.

7. High dust removal efficiency, greatly improving the sight of the roadheader driver, eliminating the potential safety hazards and improving the section quality and production efficiency.

How to maintain the dust removal equipment, before this, we have explained the consequences of the industrial vacuum cleaner not paying attention to the maintenance or the incorrect method of use. Below we will introduce how to properly use the vacuum cleaner and maintenance.

1. There are many types of dust removal equipment, and the models, specifications, structural performance and functional characteristics are all different. Read the instructions carefully before use to avoid damage to the industrial vacuum cleaner due to improper use and the safety of the user.

Second, the ambient temperature of the general industrial vacuum cleaner should not exceed 40 degrees, the workplace should not be above 1000 meters above sea level, should have a good ventilation environment, and can be used in a dry indoor environment where there is no flammable or corrosive gas in the air.

3. Dry dust removal equipment is not allowed to absorb water, and wet hands cannot operate vacuum cleaners. If you need to clean all the large paper balls, plastic cloth or waste waste larger than the diameter of the suction pipe, it should be removed beforehand, otherwise it will easily cause the suction pipe to be blocked. 6. When the industrial vacuum cleaner draws liquid substances, remove the filter element and pay attention to emptying the liquid in time.

Fourth, connect the ground wire to ensure safe use of electricity. It is best not to exceed 8 hours for a typical industrial vacuum cleaner to work continuously, mainly to prevent the motor from overheating and burning. The specially designed industrial vacuum cleaner can work continuously for 36 hours without stopping due to the special cooling system. It can be used with the machine tool.

5. When using an industrial vacuum cleaner equipped with an automatic winding device, pull the power cord out of the available length. Do not pull the power cord. If you see the yellow or red marking on the power cord, you must stop pulling it out. Prevent the power cord from being pulled too far. If you need to rewind the power cord, it will automatically retract when you press the button directly.

6. Do not over-expand and bend the industrial vacuum cleaner hose or fold it off frequently, which will affect the life of the industrial vacuum cleaner hose.

7. Check the power plug and power cord of the dust removal equipment for damage. The leakage will burn the industrial vacuum cleaner motor.

8. Move the dust removal equipment to be careful not to be hit, to prevent the industrial vacuum cleaner barrel from leaking and leaking, and to reduce the suction of the industrial vacuum cleaner.

9. When the machine is not in use, it should be placed in a ventilated and dry place. It does not support industrial vacuum cleaners that work continuously for a long time. The continuous working time should be controlled within the working time supported by the industrial vacuum cleaner. Do not overload the work, otherwise it will affect the life of the industrial vacuum cleaner.

10. If the main unit of the dedusting equipment is hot, has a burnt smell, or the industrial vacuum cleaner is abnormally shaking and squeaking, it should be stopped immediately for repair, and do not overload the industrial vacuum cleaner.